Видео

Did we break the ABS sensor wire?

So it works viceversa ? The door for would fit a two door ?

Hi, Im looking for the vacuum hoses on my X6 e71 35i ?

well done.

I was interested but then Kinda confused and disappointed. Meh. I do Wish Bronco engines were louder tho, my first car was an 01 GT with a V8 so loud AF is kinda what I like.

Excuse me, where did you buy the spacers for the stabilizer bar? I can't find them. I have a Ford F150.

Great job. mine is a 04 envoy xuv. Thinking of removing the dash so I can get to the air mode actuator, and defrost actuator. Looks daunting. You make it look simple. Thanks for the video R.

How long did you let each step dry??😊

I thought primer first

My Ducati scrambler top Pipe is less than two fingers away from my bare calf, I hope the wrap is enough plus a heat guard, but I also have a plastic timing belt cover that’s 5mm clear of the lower pipe, so I’ll buy an aftermarket cover of metal (probs aluminum) just hope I don’t have to ceramic coat

Thank you for good video

Definitely had helped me , I’m having the rear hub noise - I’m about to keep up the part today and try my luck later tonight - thanks brother

3.8 is known for lifter tick bet after you do manifolds bet you are doing a lifter job….OEM lifters last to about 80,000 miles.

Man I hope mine goes this smooth. Got parts ordered today

DANG! In that left well in my trunk I got all electronics for the NAV and amp...

Man... This was great. Its the first video showing "WHERE" the vacuum hoses are located in the trunk and how to get to them! PROPS for that! Will this work to stop the Exhaust rattling? In my diag I hear this rattling so I used a small rod to push in the pipe on the Actuator with the car running and it stopped. This tells me I most likely have a vacuum leak. So again, might this b a good work-around for that problem? THANKS

whished i could get you to repair my dash. you know what you are doing.

I know it works on a c5 Z06 because I did mines. But the short line it's spouse to be steel line

This literally saved me thank you so much!

JJ, is the spray paint you used here still holding up nicely?

Will this work on my bmw 523i e60 2005?

what is the black square thing in the center of the bronco behind the bumper ?

This is very informative. I was quoted 10 hours of labor to replace my 2010 Silverado dash. Thanks to this video I’m confident that with w few purchased tools and a trip to the junkyard, I can replace my dashboard myself. Thank you!

Why do people think bagging these is so cool.... it just makes them look like trashy... what comes to mind is a poor gangster type with a lot of tattoos and piercings

Stealing tailgates?! Tailgate theft is not a problem here in Albuquerque. They just steal your truck.

Well done 🏅

you should put leds on your turn signals as well😭

What make are these LED lights from Amazon?

Do you know how to reset the “My Key” restrictions without the admin key?

Is it possible to put left side back on right side instead of rotating strut 180 degrees? my vice is not set up at the moment

You forgot the sun load sensor

I recently got new Bilstien shocks n struts. My tech cut the bump stops so the struts have more travel to make a smoother ride.

can i have the link to the supercharger kit please? i really want to add this to my truck and this one looks great!

Can this same work be done on a 2019 ram 1500 notice you’re description says applies to all dodge ram 2010 through 2018?

Link for the Supercharger kit

Bro ditch the stock trans and go with a 4r70w from a 99-04 mustang 3.8. Get a full manual valve body and get a 3k stall converter. You'll need a rachet shifter as well. It'll wake the truck the fuck up 😂 trust me I'm running a 393 stroker on my 96 f150 single cab and it woke the truck up night and day difference

Hey JJ, are they still holding up after 4+ years?

Hey bro how many washers should I use if I have an even sag on both sides ?

Sounds GR8 🎉🎉🎉

Great video for something that I need to tackle on my 2011. My dash is badly cracked up. I need that stapler - new tool purchase 🙂

Nice work matey 👍😊 Cheers from Aus 🇦🇺 🍺🕺

Wow! That track is awesome-where is it located and the name? Nice video & fun car too!

Thanks m8

Hello, can you please send me the link on where you bought these.

This happened to me. The same fuse kept blowing because of a bad comfort access door handle sensor.

Did not work on 2012 altima

Thanks for this hack. I have a F86 X6M, where is the actuator?

Excellent video.

How did you know which injectors to order? I have a sierra 1500 w 5.3 and there’s three types of flow injectors

newest mud flaps: ruclips.net/video/bLrFKDnrCq4/видео.html